Cisco Meraki - MR Series Setup Guide

This guide will walk you through the process of creating a Meraki Network configured to support Yelp WiFi. Once you have a Network created, you will be able to add access points and begin using them to create your Yelp WiFi hotspots.

Location and scanning 

1. Navigate to your Meraki dashboard at meraki.cisco.com

2. In the left navigation panel, go to Network-wide > General

3. Scroll down to 'Traffic Analysis' and ensure it is 'enabled'



Screen_Shot_2017-11-24_at_11.02.29_AM.png

4.  Scroll to Location and scanning and configure the following:

  • Analytics = Analytics enabled
  • Scanning API = Scanning API enabled
  • Validator = ** Send your validator to your Yelp WiFi representative**
    (they will use this to generate your Post URL and Secret needed below)

Screen_Shot_2017-11-24_at_11.17.50_AM.png

5. Add a Post URL

  • Post URL = http://checkin.getturnstyle.com/**From your Yelp WiFi representative**
  • Secret = **From your Yelp WiFi representative**
  • API Version = 2.0
  • Click 'Validate' – if successful, a confirmation message will appear

Screen_Shot_2017-11-24_at_11.18.36_AM.png

6. Be sure to Save your changes before navigating to the next section

Note: Data collection will begin within 24 hours


Captive Portal/ Access Control

1. Navigate to Wireless > Access Control

2. Under 'Network Access', set Association Requirements = Open (no encryption)

3. Under 'Network Access' set Splash page = Sign-on with my RADIUS server

Screen_Shot_2017-11-24_at_11.27.18_AM.png


4. Scroll down the page to RADIUS for Splash Page and configure the following:

  • RADIUS Server 1 Host = 52.22.120.222
  • RADIUS Server 2 Host = 52.20.198.151
  • Port (1&2) = 1812
  • Secret (1&2) = **From your Yelp WiFi representative**
  • Test to confirm (username and password are both “test")

Screen_Shot_2017-11-24_at_11.32.26_AM.png


5. Scroll down to 'Captive Portal Strength' and configure to = 'Block all access until sign-on is complete'

6. Walled Garden = Walled garden is enabled

7. Walled Garden Ranges = Enter the following domains:

*.yelpwifi.com
*.getturnstyle.com
*.facebook.com
*.fbcdn.net
connect.facebook.net
*.linkedin.com
*.licdn.com
*.twitter.com
*.twimg.com
*.bootstrapcdn.com
s3.amazonaws.com
*.newrelic.com
*.akamaihd.net
*.nr-data.net

Note: Some customers may receive an error at this stage indicating that only IP ranges are accepted. If this is the case, please contact Meraki and request for "domain based Walled Garden to be enabled".

8. Be sure to Save your changes before navigating to the next section

Screen_Shot_2017-11-24_at_11.40.02_AM.png

Splash Page

1. Navigate to Wireless > Splash Page

2. Be sure to select the desired  SSID at the top for your Yelp WiFi configuration

3. Select custom splash URL = http://wifi.getturnstyle.com

Screen_Shot_2017-11-24_at_11.46.32_AM.png


4. Scroll down to the 'Splash Behavior' section

  • Select: "The URL they were trying to fetch"

Screen_Shot_2017-11-24_at_11.53.04_AM.png

 


That's it, your Meraki dashboard is now configured to support Yelp WiFi!

 

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

Comments